ND AGGREGATE™
ND AGGREGATE™ - traction grains for SKID SAFE™ to create our No-Slip Skid Safe System™
ND AGGREGATE™ – traction grains for SKID SAFE™ to create our No-Slip Skid Safe System™
Price range: $19.99 through $109.99
From $0.35 /sq. ft.
Main Benefits
- Creates a highly non-slip surface when used with SKID SAFE™
- Highly durable: Made from high-quality, extremely hard, and durable materials (aluminum oxide or silicon carbide)
- Long-lasting guarantee: Our no-Slip Skid Safe System™ is guaranteed for 5 years on all flooring materials with proper application and maintenance
- Aesthetically subtle: Available in White, Black, Brown and Brown, becomes barely visible or on appropriate light – colored floors
- Cost-effective coverage: One pound of the product covers approximately 160 square feet
🏠 Floor Surface Treatment Selector
Find the perfect non-slip protection solution for your surface
Q1: Floor Surface needing non-slip protection
Q2: Area to be covered
Q3: Do you want to add ND AGGREGATE?
Traction grains e.g. for swimming pools, entrances, exterior walkways, etc.
🎯 Recommended Product
Graffiti Protection Selector
Find the right ND Graffiti Shield kit for your surface
Q1: Surface needing protection
Recommended Product
Surface Type:
Coverage Area:
Add Remover:
Product Recommendation:
Slip Finish
Watch our short video that shows how to properly broadcast ND AGGREGATE™ We highly recommend that you practise to properly apply the aggregate on to our SKID SAFE™ by test applying it to any loose tiles, plastic sheet, or a small floor area before proceeding with the entire job. Apply the first coat of SKID SAFE™ to a small area of the floor (using a new, pre-washed mop, or a sponge roller) so that it is easy for you to stand over it and broadcast ND AGGREGATE™. While SKID SAFE™ is still wet hold a small amount of the aggregate in your hand and throw it straight up slightly. The aggregate will fall evenly over this wet SKID SAFE™ area.
Coat of SKID SAFE™:
You can also use a sieve to evenly spread the aggregate. Then, apply another small area of SKID SAFE and repeat the above process until the entire floor area has been sealed with a first coat of SKID SAFE with the broadcast of our ND AGGREGATE™. Use a fan or a blower to help blow dry each coat of SKID SAFE. Open windows for ventilation. Apply in low to moderate humidity. Each coat should dry in about 30 – 60 minutes. High humidity, low temperature, no air circulation will greatly increase the drying and curing times.
When the first coat is absolutely dry use a paint roller (sponge, or short nap) or a low pressure sprayer (about 35-65PSI) to apply coats 2-6 so as not to disturb the aggregate which a sponge mop will. Each successive coat must be absolutely dry to the touch before applying the next coat.
After the entire 6 coat of SKID SAFE™ is completed, 96 hours more time is needed to allow our finish to CURE (GET VERY HARD). If you cannot close the floor to foot traffic for the next 96 hours, cover the floor with a cardboard masked down to enable foot traffic after 8 hours of drying time. Remove the cardboard after 4 DAYS. Use normally. Do not cover the floor with any plastics, or rubber during the cure time.
Maintenance
Clean this floor ONLY with a NEUTRAL CLEANER (pH of 7)! Other cleaners can dull, and or damage SKID SAFE™. You may clean the floor with a soft nylon brush, light scrubbing machine and NEUTRAL CLEANER, or with a powerwasher. Do not use disinfectants known to harm plastics/floor finishes. Do not use cotton, or sponge mops. When over time you observe a loss of gloss on certain areas apply a light coat of SKID SAFE™ over them.
Watch our short video that shows how to properly broadcast ND AGGREGATE™ We highly recommend that you practise to properly apply the aggregate on to our SKID SAFE™ by test applying it to any loose tiles, plastic sheet, or a small floor area before proceeding with the entire job. Apply the first coat of SKID SAFE™ to a small area of the floor (using a new, pre-washed mop, or a sponge roller) so that it is easy for you to stand over it and broadcast ND AGGREGATE™. While SKID SAFE™ is still wet hold a small amount of the aggregate in your hand and throw it straight up slightly. The aggregate will fall evenly over this wet SKID SAFE™ area.
Coat of SKID SAFE™:
You can also use a sieve to evenly spread the aggregate. Then, apply another small area of SKID SAFE and repeat the above process until the entire floor area has been sealed with a first coat of SKID SAFE with the broadcast of our ND AGGREGATE™. Use a fan or a blower to help blow dry each coat of SKID SAFE. Open windows for ventilation. Apply in low to moderate humidity. Each coat should dry in about 30 – 60 minutes. High humidity, low temperature, no air circulation will greatly increase the drying and curing times.
When the first coat is absolutely dry use a paint roller (sponge, or short nap) or a low pressure sprayer (about 35-65PSI) to apply coats 2-6 so as not to disturb the aggregate which a sponge mop will. Each successive coat must be absolutely dry to the touch before applying the next coat.
After the entire 6 coat of SKID SAFE™ is completed, 96 hours more time is needed to allow our finish to CURE (GET VERY HARD). If you cannot close the floor to foot traffic for the next 96 hours, cover the floor with a cardboard masked down to enable foot traffic after 8 hours of drying time. Remove the cardboard after 4 DAYS. Use normally. Do not cover the floor with any plastics, or rubber during the cure time.
Maintenance
Clean this floor ONLY with a NEUTRAL CLEANER (pH of 7)! Other cleaners can dull, and or damage SKID SAFE™. You may clean the floor with a soft nylon brush, light scrubbing machine and NEUTRAL CLEANER, or with a powerwasher. Do not use disinfectants known to harm plastics/floor finishes. Do not use cotton, or sponge mops. When over time you observe a loss of gloss on certain areas apply a light coat of SKID SAFE™ over them.
